Santa Fe Roof Pros provides professional metal roofing in Santa Fe, NM for residential and commercial properties across northern New Mexico. Metal is genuinely native here, which surprises people who picture Santa Fe as a purely flat-roofed town. Territorial and Northern New Mexico houses put pitched metal over the portal and over hipped roofs hidden behind the parapet line, and have done since the railroad brought panels in.
The slope rules are specific and worth knowing before you start shopping. The code allows standing seam down to a quarter-inch in twelve, permits half an inch in twelve for lapped non-soldered seams assembled with sealant, and requires a full three in twelve for lapped non-soldered seams without it. Most of the cheap corrugated bids you will be shown fall squarely into that last category.
We install two systems mostly. Twenty-four-gauge mechanically seamed panel on anything with real weather exposure or a long uninterrupted run, and snap-lock on shorter portal roofs and porch sheds where the run stays under roughly twenty feet. Exposed-fastener panel has an honest place on outbuildings and barns, but each exposed screw depends on a neoprene washer that hardens, shrinks and finally quits. We will quote both and show you the difference honestly rather than steering you.
Thermal movement drives most of the detailing. A panel run in Santa Fe sees a wide daily swing under unusually intense sun, so long runs get floating clips and the fixed point placed deliberately rather than wherever the crew happened to start setting panel. Runs that were face-fastened at both ends oil-can first, then elongate their own holes, then leak in about six years. Panel length dictates clip type, so we measure the run before specifying.
The interesting work is always the transition. Where a pitched metal roof drains into a parapet-enclosed flat section, or discharges toward a canale, the code wants taper board or an equivalent to create a uniform substrate between the two deck levels. Getting that single junction right is most of the reason these hybrid Santa Fe roofs either succeed or fail.
One honest note on color and finish. A bright galvalume roof reads very loudly against a stuccoed street, and inside the city's five historic districts a change in visible finish can need approval before it goes up. We would far rather walk that question with you before fabrication than after the panels are sitting on the ground. Darker matte finishes usually read better on a Santa Fe street and cost the same.
Our licensed and insured team brings the right materials and equipment to every job — canale pans lapped six inches inside the parapet, continuous parapet coping wrapped down both faces, sprayed polyurethane foam with a silicone topcoat, 60 and 80 mil TPO and PVC single-ply membrane, torch-applied two-ply SBS cap sheet, tapered polyisocyanurate cut to a quarter inch per foot — and backs the work with a written workmanship warranty. We serve Santa Fe and nearby communities including Eldorado at Santa Fe, La Cienega, Agua Fria, Pojoaque.
What We Handle
Everything our metal roofing in Santa Fe covers
One crew, one point of contact, and the full range of metal roofing work in Santa Fe, NM. If it is on this list we do it in house rather than handing it to a subcontractor:
- metal roofing santa fe
- standing seam metal roof santa fe nm
- metal roof santa fe county
- pro panel roof new mexico
- territorial style metal roof
- portal roof metal
- corrugated metal roof santa fe
- metal roof installation northern new mexico
- santa fe metal roofer
- snap lock standing seam
- metal roof over portal
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Santa Fe services.
Materials, equipment and how we do metal roofing
The difference between metal roofing that lasts and metal roofing that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with canale pans lapped six inches inside the parapet, continuous parapet coping wrapped down both faces, sprayed polyurethane foam with a silicone topcoat, 60 and 80 mil TPO and PVC single-ply membrane, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Santa Fe job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in northern New Mexico means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do metal roofing outside Santa Fe
Santa Fe Roof Pros covers Santa Fe and the surrounding communities of northern New Mexico. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Metal Roofing in Eldorado at Santa Fe, NM — Santa Fe County, population 6,005
- Metal Roofing in La Cienega, NM — Santa Fe County, population 3,885
- Metal Roofing in Agua Fria, NM — Santa Fe County, population 2,913
- Metal Roofing in Pojoaque, NM — Santa Fe County, population 2,071
- Metal Roofing in Nambé, NM — Santa Fe County, population 1,907
- Metal Roofing in Tano Road, NM — Santa Fe County, population 1,573
Start on the Santa Fe Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Santa Fe Chooses Santa Fe Roof Pros
- ✓We test drainage with a hose and a clock against the state's half-inch, 48-hour standard before we quote anything.
- ✓Every canale is rebuilt with a metal pan lining running six inches inside the parapet, not patched with sealant.
- ✓Parapet caps are held with cleats at the vertical faces because the code forbids fasteners across the horizontal top.
- ✓We price pumice removal openly, because New Mexico no longer permits granular fill to stay in a roof assembly.
The standards behind metal roofing
Quality here is not a matter of opinion — it is written down. The metal roofing work we do in Santa Fe follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every metal roofing project in Santa Fe gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free metal roofing free estimate in Santa Fe, or request a quote and we'll get right back to you.